APPLICATION

The solution is used for manufacturing self-leveling floors (interlayers) on almost any pre-prepared basis in residential and public buildings. The thickness of the layer is 5-20 mm. Pouring into one layer. The ready-made screed meets all the requirements for floor interlayers, which can be applied to all types of coatings (parquet, linoleum, carpet coatings, tiles, paint, etc.)

PREPARATION OF THE SURFACE

The most important factor is the preparation of the substrate. The main requirement is that the substrate should be strong and clean (cementitious grounds – at least 28 days). Before applying floors from the base, it is necessary to remove not only coarse dirt, but even dust, preferably with a vacuum cleaner. Large damages, for example, broken parts of the screed or voids should be filled with putty. All the grounds must be primed with primer Artisan No. 7, or Artisan No. 8 super, depending on the requirements for the substrate. Do not wet the surface of the substrate.

PERFORMANCE OF WORK

The mixture is mixed with water with a low-speed stirrer until a homogeneous mass without lumps is obtained. Wait 5 minutes and mix again. Then pour the solution onto a prepared base and distribute it with a roller, a hard broom, a rubber straps and similar tools. It is recommended to roll the surface of the poured layer with a spiked roller to remove air lock. You can use a piston or auger pump to feed the solution. In the event of a break in operation for more than 20 minutes, the machine should be cleaned with water. The hardened solution can only be removed mechanically.

NOTE!

Excess water reduces the mechanical strength of the solution and leads to delamination. After 36 hours on the floor you can walk. It is possible to apply various coatings to the floor surface in 7-28 days, taking into account the requirements of the state building norms B.2.6-22-2001. The most effective result is achieved at t + 20 ° C and 60% relative humidity. In other conditions, the operating parameters of the mixture may vary. The manufacturer is not responsible for the incorrect use of the material, nor for application of it for purposes and conditions not provided for by the instruction.

SAFETY PRECAUTIONS

The mixture contains cement, which when combined with water forms alkali. It is necessary to prevent the hitting impregnation on the skin and mucous membranes. All work should be carried out in goggles, rubber gloves and protective clothing. Provide fresh air. In case of contact with skin or eyes, rinse thoroughly with water and if necessary, consult a doctor.

EXPIRATION DATE

In dry conditions and hermetic packaging the period of storage is at least 12 months from the date of manufacture.

PACKAGING

The dry mix is packaged in bags of 25 kg.

TECHNICAL CHARACTERISTICS

Composition: mixture of cement with mineral fillers and special additives

Quantity of water for solution preparation, l / kg :  0,22-0,24

Proportion of batch, l / kg : 5,0-6,0/25

Time of use, min, not less than: 20 min

Substrate temperature, ° С: +10 to +25

Compressive strength, MPa, not less than: 15.0

Ready for use: after 7-28 days

Consumption, kg / m2 / mm: around 1.6

LAYER THICKNESS 5 – 20 mm

CONVENIENT IN APPLICATION

PERSISTENT TO THE CONCENTRATED LOAD

HIGH STRENGTH

PERFECTLY SMOOTH SURFACE

DOES NOT BURN

ECOLOGICALLY CLEAN

Mixture “Artisan” Ц.2.ПР1

ДСТУ БВ.2.7-126:2011

Hygienic conclusion of the Ministry of Health of Ukraine.

APPLICATION

The solution is used for manufacturing self-leveling floors on almost any pre-prepared basis, in residential and public premises. The thickness of the layer is not more than 15 mm. Pour into 1 coat. The finished screed meets all the requirements of finishing floors, which can be applied to all types of coatings (parquet, linoleum, carpet, tile, paint, etc.).

PREPARATION OF THE SURFACE

The most important factor is the preparation of the base. The basic requirement – the basis should be strong and clean (aging of cement bases – 28 days). ). Before applying the floors from the base, it is necessary to remove not only coarse dirt, but even dust, preferably with a vacuum cleaner. To remove oils, fats, wax, paraffin, paints and other contaminants from the surface of the substrate, it is necessary to use alkaline solutions, and then rinse with water. Large damages, for example, broken pieces of screed, cracks or voids should be removed and plastered. All the grounds must be treated with Primer “Artisan No. 7”. Do not wet the surface of the base with water.

PERFORMANCE OF WORK

The mixture is mixed with water approximately on a bag of 25 kg – up to 6 liters of water and mixed using a stirrer with low speed, until a homogeneous mass without lumps. Wait 5 minutes and mix again. Then pour the solution onto the prepared substrate and distribute it with a roller, a hard broom, a rubber bar and similar tools. It is recommended to roll over the surface of the poured layer with a spiked roller to remove air plugs. You can use a piston or auger pump to feed the solution. In cause of a break in operation for more than 20 minutes, the machine should be cleaned with water. The hardened solution can only be removed mechanically. The diluted solution must be protected from drying.

NOTE!

Excess water reduces the mechanical strength of the solution, the solution can be delaminated. Keep away from high temperatures and drafts. After 8 hours, the floor is ready for use. The manufacturer is not responsible for improper use of the material, as well as its application in order and conditions not stipulated by the instruction.

SAFETY PRECAUTIONS

The mixture contains cement, which, when mixed with water, forms an alkali. Work should be in rubber gloves. If the solution gets into the skin or eyes, rinse them with plenty of water, if necessary, consult a doctor.

EXPIRATION DATE

In dry conditions and hermetic packaging the period of storage is at least 12 months from the date of manufacture.

PACKAGING

The dry mix is packaged in bags of 25 kg.

TECHNICAL CHARACTERISTICS

Composition: Mixture of cement with mineral fillers and special additives

Proportion of the mixture, l / kg: 0,22 – 0,24

Time of use, min:  to 20

Application temperature, ° С: from +5 to +30

Compressive strength, MPa, not less than: 15,0

Readiness for operation, hours, after: 36

Consumption, kg / m2 / mm, approx.: 1,5

LAYER THICKNESS 2-15 MM

SUSTAINABLE TO CONCENTRATED LOAD

HIGH-STRENGTH

PERFECT SMOOTH SURFACE

CONVENIENT IN APPLICATION

DOES NOT BURN

ENVIRONMENTALLY PURE

Mixture “Artisan” Ц.2.ПР2

ДСТУ БВ.2.7-126:2011

Hygienic conclusion of the Ministry of Health of Ukraine.

APPLICATION

The solution is used for manufacturing self-leveling floors on almost any pre-prepared basis, in residential and public premises. The thickness of the layer is not more than 10 mm. Pour into 1 coat. The finished screed meets all the requirements of finishing floors, which can be applied to all types of coatings (parquet, linoleum, carpet, tile, paint, etc.).

PREPARATION OF THE SURFACE

The most important factor is the preparation of the base. The basic requirement – the basis should be strong and clean (aging of cement bases – 28 days). Before applying the floors from the base, it is necessary to remove not only coarse dirt, but even dust, preferably with a vacuum cleaner. Large damages, for example, broken pieces of screed, cracks or voids should be removed and plastered. All the grounds must be treated with Primer “Artisan No. 7”. Do not wet the surface of the base with water.

PERFORMANCE OF WORK

The mixture is mixed with water approximately on a bag of 25 kg – up to 6 liters of water and mixed using a stirrer with low speed, until a homogeneous mass without lumps. Wait 5 minutes and mix again. Then pour the solution onto the prepared substrate and distribute it with a roller, a hard broom, a rubber bar and similar tools. It is recommended to roll over the surface of the poured layer with a spiked roller to remove air plugs. You can use a piston or auger pump to feed the solution. In cause of a break in operation for more than 20 minutes, the machine should be cleaned with water. The hardened solution can only be removed mechanically. The diluted solution must be protected from drying.

NOTE!

Excess water reduces the mechanical strength of the solution, the solution can be delaminated. Keep away from high temperatures and drafts. After 8 hours, the floor is ready for use. It is possible to apply various coatings to the floor surface after 7-28 days, taking into account the requirements ДБН В.2.6-22-2001.

The manufacturer is not responsible for improper use of the material, as well as its application in order and conditions not stipulated by the instruction.

SAFETY PRECAUTIONS

The mixture contains cement, which, when mixed with water, forms an alkali. Work should be in rubber gloves. If the solution gets into the skin or eyes, rinse them with plenty of water, if necessary, consult a doctor.

EXPIRATION DATE

In dry conditions and hermetic packaging the period of storage is at least 12 months from the date of manufacture.

PACKAGING

The dry mix is packaged in bags of 25 kg.

TECHNICAL CHARACTERISTICS

Composition: Mixture of cement with mineral fillers and special additives

Proportion of the mixture, l / kg: 5,5-6/25

Time of use, min, not less than: 20

Application temperature, ° С: from +5 to +30

Compressive strength, MPa, not less than: 15

Readiness for operation, hours, after: 8

Consumption, kg / m2 / mm, approx.: 1.6

LAYER THICKNESS 2-10 MM

CONVENIENT IN APPLICATION

FAST CURING

HIGH-STRENGTH

PERFECT SMOOTH SURFACE

DOES NOT BURN

ENVIRONMENTALLY PURE

Mixture “Artisan” Ц.2.ПР1

ДСТУ БВ.2.7-126:2011

Hygienic conclusion of the Ministry of Health of Ukraine.