APPLICATION

Gypsum-perlite plaster is used in finishing works for manual plastering and leveling of walls and ceilings with any type of surface (concrete, gypsum, stone, brick, cellular-concrete) as well as for the preparation of grounds for painting, wallpaper, facing work inside rooms with normal humidity in residential, administrative and industrial buildings. Gypsum plaster allows you to get a smooth surface that does not require putty before the subsequent work. Has a short drying period. It does not form cracks and does not fade, even with a thick layer. Creates bases with improved heat and sound insulation properties for the most comfortable living conditions. In the rooms a favorable microclimate is formed.

Gypsum-perlite plaster – is a method of leveling walls, with the help of screed strips, which is the only effective alternative to gypsum boards. The main advantage – saving the volume of the internal space, as well as ease of repair and maintenance for long-term operation (gypsum cardboard systems should be dismantled). It is possible to apply plaster in the usual way, but the most qualitative result is obtained when performing work using screed strip.

PREPARATION OF THE SURFACE

The surface must be dry and firm, free of dust, oils, dirt and other contaminants of organic origin. To improve the adhesion of the solution to the substrate; for binding of dust residues; for highly absorbent and cementitious substrates – mandatory priming with “ARTISAN No. 7” deep penetration primer is required.

PREPARATION OF THE MORTAR

The dry plaster mixture is mixed with clean water until it is uniform. The mixture is poured into the water. The solution is held for 5-10 minutes, then mixed again. After that, the mixture is ready for use.

PERFORMANCE OF WORK

Plastering is carried out according to predetermined screed strips. The plaster solution is applied to the surface in one layer and leveled. The optimum layer thickness is 10 mm (the minimum is 5 mm, the maximum is 30 mm). After the beginning of setting, the surface is treated with a wide spatula, and after 15-20 minutes rubbed with a sponge grater, moistened with water and smooth with a metal spatula, obtaining an absolutely smooth surface. Plastering in two layers is allowed. For this, it is necessary to apply a notch on the first layer that has not yet hardened, and then apply the second on the dried surface of the first layer.

The manufacturer is not responsible for misuse of the material and its application in the manner and conditions other than those specified in these instructions.

SAFETY PRECAUTIONS

All components that make up the mixture are non-toxic and harmless to health. Work with the material in accordance with accepted standards.

EXPIRATION DATE

In dry conditions and hermetic packaging the period of storage is at least 12 months from the date of manufacture.

                                                                                           PACKAGING             

The dry mix is packaged in bags of 30 kg.

TECHNICAL CHARACTERISTICS

Composition: mineral raw materials with gypsum and special additives.

Amount of mixing water, l / kg: 0,35 – 0,5

Consumption, kg / m2 / mm:  1

Compressive strength, MPa, not less than: 1,5

Time of use, hours:   1

Optimum application temperature, ° С: from +10 to +30

RECOMMENDED LAYER THICKNESS – 10 MM

HIGH ADHESION

HIGH PLASTICITY

EASY TO USE

ENVIRONMENTALLY PURE

Mixture “Artisan Г.2.ШТ6

ДСТУ БВ.2.7-126:2011         

Hygienic conclusion of the Ministry of Health of Ukraine.

APPLICATION

Plaster “Mechanics” is used for plastering walls and ceilings with interior decoration of premises. It is applied to all standard mineral substrates either manually or mechanically.

PREPARATION OF THE SURFACE

The surface should be dry and durable, free from grease, old paints, crumbling plaster. To ensure high-quality and long-term exploitation, it is recommended to prime all grounds with primer  “Artisan No. 7” , or “Artisan No. 8 Super”, depending on the requirements to the substrate.

PERFORMANCE OF WORK

When plaster is applied mechanically, the dry mix is mixed with water in the installation, in a continuous automatic mode. The water supply to the plaster station should be adjusted in accordance with the consistency. Apply the plaster by spraying and leveling. In the event of a break in operation for more than 15 minutes, the machine should be cleaned with water. The hardened solution can only be removed mechanically. The average layer thickness is 15 mm (min 10 mm). Plastering in two layers is allowed. At the end of the work, immediately flush the tool and the plaster station.

The manufacturer is not responsible for misuse of the material and its application in the manner and conditions other than those specified in these instructions.

SAFETY PRECAUTIONS

All components that make up the mixture are non-toxic and harmless to health. Work with the material in accordance with accepted standards.

EXPIRATION DATE

In dry conditions and hermetic packaging the period of storage is at least 12 months from the date of manufacture.

PACKAGING

The dry mix is packaged in bags of 30 kg.

TECHNICAL CHARACTERISTICS

Composition: mixture of gypsum, mineral fillers and special additives

Amount of mixing water for manual application method, l / kg:  0,35 – 0,45

Time of use of the solution for manual application, mm, not less than:  60

Time of use, min, not less than: 60

Optimum temperature for solution use, ° С: from +5 to +30

Maximum layer thickness per application, mm:  30

Compressive strength, MPa, not less than:  2,0

Consumption for layer thickness 10 mm, kg / m2:  9-10

Thickness of a layer in one pass:

• min-10 mm
• -30 mm

Drying: in 7 days

Rotor-stator (PFT): D6-3

Water consumption:  650 l./hour

Hose Diameter:  25 mm.

MAXIMUM LAYER THICKNESS 30 MM

HIGH-PLASTIC

WHITE SMOOTH SURFACE

EASY TO USE

DOES NOT BURN

ENVIRONMENTALLY PURE

Mixture “Artisan”  Г.2.ШТ6

ДСТУ БВ.2.7-126:2011         

Hygienic conclusion of the Ministry of Health of Ukraine.

APPLICATION

The mixture is intended for machine / as well as manual / plastering of brick (from ceramic, silicate, concrete bricks), concrete (including lightweight concrete), cement, cement-lime, lime-sand bases, 5-20 mm layer inside and out buildings, as well as in rooms with high humidity. Can be used as a base for decorative plasters and paint coatings.

PREPARATION OF THE SURFACE

The substrate must be smooth, dry, strong, and free from dust, dirt, grease, paint and other materials that reduce adhesion. The crumbling layers must be removed. All the grounds need to be pre-treated with the primer number 7 or, if necessary, primer number 8 or primer number 15 of trademark “Artisan”.

PERFORMANCE OF WORK

For machine application, the water supply must be adjusted in accordance with the required consistency. With a properly selected consistency, the mixture will gently blend during application. Apply the mixture with a spray and level with a metal strip or similar tool. A multi-layer application of the plaster mixture is allowed, but in one pass the thickness of its layer should not exceed 20 mm. The subsequent layer is applied after the beginning of setting the previous / approximately 24 hours after application. When manually applied, the mixture is poured into water at room temperature and mixed mechanically until a uniform composition is obtained. The consistency of the mixture is controlled by the amount of water. The final surface treatment is carried out after the beginning of its setting, approximately 3-4 hours after application, depending on the substrate and weather conditions. The surface is moistened with a spongy grater. Smoothing can be done with a metal spatula, grater or other tool. In order to avoid the occurrence of defects, the applied plaster layer should be protected from rain, strong wind, drafts, direct sunlight. The room in which the work is done, it must be ventilated.

The manufacturer is not responsible for misuse of the material and its application in the manner and conditions other than those specified in these instructions.

SAFETY PRECAUTIONS

The mixture contains cement and lime, when it is watered, it forms alkali. Work should be in rubber gloves. If the solution gets on the skin or eyes, they should be rinsed with plenty of water, if necessary, consult a doctor.

EXPIRATION DATE

In dry conditions and hermetic packaging the period of storage is at least 12 months from the date of manufacture.

PACKAGING

The dry mix is packaged in bags of 30 kg.

TECHNICAL CHARACTERISTICS

Composition: mixture of cement and lime with mineral aggregates, perlite and special additives

Maximum particle size, mm:  1,2

Temperature of use:  from +10 to +25

Compressive strength, MPa, not less than:  7,0

Strength of adhesion to the substrate, MPa, not less than:  0,3

Consumption of the mixture, kg / m2 / mm: 1,35

APPLIES WITH LAYER 5-20 MM

HYDROPHOBIZED

VAPOR- PERMEABLE

FROST-RESISTANT

EASY TO USE

ENVIRONMENTALLY PURE

Mixture “Artisan”  Ц.1.ШТ2

ДСТУ Б В.2.7-126:2011

Hygienic conclusion of the Ministry of Health of Ukraine.

APPLICATION

The mixture is intended for manual and machine plastering of any mineral surfaces: brick, stone, concrete, pumice, gypsum plaster, foam concrete inside and outside buildings. After drying, the surface can be treated with any vapor-permeable paints.

PREPARATION OF THE SURFACE

The substrate must be smooth, dry, strong, free from dust, dirt, grease, paint and other materials that reduce adhesion. The crumbling layers must be removed, if necessary, the base is pre-treated with primer No. 7, earth No. 8 super or primer No. 15 (Betonkontakt) of the trade mark “Artisan”.

PREPARATION OF THE MORTAR

For manual application.

The bag of the mixture is completely poured into a working container with water and thoroughly mixed until a uniform composition is obtained; the consistency of the mixture is adjusted to the necessary by addition of water. Do not violate the specified procedure for preparing the mortar mixture. Otherwise, a solution with other properties, including adhesion, heat-insulating, strength, etc., will be obtained. Mixing of the dry mixture with water must be carried out with a mixer at low speed for 5 minutes.

PERFORMANCE OF WORK

Screed strip are mounted on the surface to be treated. The mortar is applied manually with a stainless steel tool or with a plastering machine. After applying, the excess mixture is removed through screed strips with special tools. The maximum layer in one pass is 25 mm. If necessary, you can apply a layer of greater thickness by re-plastering the surface. After setting the mixture, screed strips are removed and their place is filled with the solution mixture. Depending on the weather and the surrounding conditions, the treated surface can be painted with paint after 2-4 days.

The manufacturer is not responsible for the misuse of the material, nor for its use for purposes and conditions not provided for by the instruction.

SAFETY PRECAUTIONS

The mixture contains cement and lime, when it is watered, it forms alkali. Work should be in rubber gloves. If the solution gets on the skin or eyes, they should be rinsed with plenty of water, if necessary, consult a doctor.

EXPIRATION DATE

In dry conditions and hermetic packaging the period of storage is at least 12 months from the date of manufacture.

PACKAGING

The dry mix is packaged in bags of 10 kg.

TECHNICAL CHARACTERISTICS

Composition: mixture of cement, lime, light fillers and corrective additives

Temperature of use:  from +5 to +30

Bulk density, kg / m3, not more than: 430

Approximate water flow per 10 kg: 7,2-7,7 l

Time of use of a mortar mixture, min, not less than: 60

Compressive strength, MPa, not less than:  3,5

Strength of adhesion to the substrate, MPa, not less than: 0,5

Coefficient of thermal conductivity, W / mK, not more than:  0,09

Consumption of the mixture, kg / m2 / mm: 0,45

WHITE COLOR

MAXIMUM LAYER THICKNESS FOR ONE PASS 25 MM

VAPOR- PERMEABLE

FROST-RESISTANT

ENVIRONMENTALLY PURE

Mixture “Artisan”  Ц.1.ШТ5

ДСТУ БВ.2.7-126:2011

Hygienic conclusion of the Ministry of Health of Ukraine.

APPLICATION

Plaster solution is used for leveling walls, ceilings, and also as a plaster solution. Thanks to special additives, the solution is highly plastic, has a high adhesion to almost any surface, does not form cracks.

PREPARATION OF THE SURFACE

Preparation of the base is carried out according ДБН В.2-22-2001. The surface of the wall on which the plaster solution is applied should be pre-cleaned of grease, old paints, plaster exfoliations, loose substrates. All the grounds must be treated with a primer of deep penetration of trademark ARTISAN “No. 7”, or “No. 8”, depending on the absorbency of the substrate. Bases that have traces of biological corrosion should be treated with antiseptic “Antifungus 14”. For very smooth bases it is recommended to use “Concrete contact” of the TM “Artisan”.

PERFORMANCE OF WORK

To obtain a solution, it is necessary to pour a dry mixture into the water and mix thoroughly by mechanical means until a homogeneous paste-like composition is obtained. Allow the solution to stand for 5 minutes, stir again. The resulting solution is applied to the prepared surface with a thickness of no more than 20 mm. With a total thickness of the plaster layer more than 25-35 mm. it is necessary to use a construction net as a reinforcing element.

All recommendations are valid at a temperature of +20 ° C and a relative humidity of 60%.

! Under adverse weather conditions (high temperature, dry wind, direct sunlight), the time of use of the solution applied to the surface can be significantly reduced.

! When the temperature of use of the solution decreases, the setting time increases.

When carrying out work should be guided by building codes and regulations. The manufacturer is not liable for improper use of the material, nor for its use for purposes and conditions not provided for by the instruction.

SAFETY PRECAUTIONS

The mixture contains cement, which, when mixed with water, forms an alkali. Work should be in rubber gloves. If the solution gets into the skin or eyes, rinse them with plenty of water, if necessary, consult a doctor.

EXPIRATION DATE

In dry conditions and hermetic packaging the period of storage is at least 12 months from the date of manufacture.

PACKAGING

The dry mix is packaged in bags of 25 kg.

TECHNICAL CHARACTERISTICS

Composition: Mixture of cement with mineral fillers and special additives

The amount of water for mixing: 5,5-5,9 l /25 kg

Time of use, min, not less than: 120

Application temperature, ° С: from +10 to +30

Strength of adhesion to the substrate, MPa, not less than: 0.3

Compressive strength, MPa, not less than: 7.5

Frost resistance, cycles, not less than: 50

Water vapor permeability mg / m * h * Pa: 0.13

Consumption, kg / m² / mm, not more than:  1.5

APPLIES WITH LAYER 5-20 MM

VAPOR- PERMEABLE

CONVENIENT IN APPLICATION

WATERPROOF

FROST-RESISTANT

ENVIRONMENTALLY PURE

Mixture “Artisan”  Ц.1.ШТ2

ДСТУ БВ.2.7-126:2011

Hygienic conclusion of the Ministry of Health of Ukraine.

APPLICATION

It is used for manual external and internal decorative plastering. It can be applied to all smooth mineral substrates, such as: concrete, cement-lime plasters, plasterboard slabs. The plaster solution can serve as a decorative layer (whiteness is not less than 85%), as the base for painting, as well as the protective layer in the “ARTISAN-WARMTH” thermal insulation system. Mineral plaster mixture is made on the basis of marble and quartz crumb to 1.5 mm. Thanks to hydrophobic additives it has a water-repellent effect, resistant to external influences of the environment.

PREPARATION OF THE SURFACE

The surface of the wall on which the plaster solution is applied should be pre-cleaned of grease, old paints, exfoliation of plasters, loose substrates. All the grounds must be treated with a deep penetration primer “ARTISAN No. 7”, or “ARTISAN No. 8”, depending on the substrate. On the smooth substrates (for roughening) or the base of heterogeneous materials (in avoiding lumens and stains on the plaster), as well as in the “Artisan-Warm” insulation system, the substrate should be preliminarily covered with primer “Artisan F-6”.

PERFORMANCE OF WORK

The mixture is poured into water and mechanically mixed until the required consistency of the solution is obtained. Allow the solution to stand for 5 minutes, stir again. During the work, it is recommended to stir the solution from time to time to obtain a homogeneous mass. The plaster is applied to the prepared substrate with a smooth stainless float. With the help of texture rollers, decorative surfaces are formed: nodules, embossing of various textures. During plastering, as well as the drying of the plaster, the surface must be protected from direct sunlight, wind and rain. It should be experimented (for this type of foundation and given weather) to establish the maximum surface that can be plastered in one technological cycle.  The plaster should be docked using the wet-on-wet method, avoiding the drying of the plastered area, otherwise the joints will be visible. Technological breaks are planned with a margin (for example: in the corners and bends of buildings, under drainpipes, at the junction of color, etc.). All recommendations are valid at a temperature of +20 ° C and a relative humidity of 60%.

! Under adverse weather conditions (high temperature, dry wind, direct sunlight), the time of use of the solution applied to the surface can be significantly reduced.

! When the temperature of use of the solution decreases, the setting time increases.

When carrying out work should be guided by building codes and regulations. The manufacturer is not liable for improper use of the material, nor for its use for purposes and conditions not provided for by the instruction.

SAFETY PRECAUTIONS

The mixture contains cement, which, when mixed with water, forms an alkali. Work should be in rubber gloves. If the solution gets into the skin or eyes, rinse them with plenty of water, if necessary, consult a doctor.

EXPIRATION DATE

In dry conditions and hermetic packaging the period of storage is at least 12 months from the date of manufacture.

PACKAGING

The dry mix is packaged in bags of 25 kg.

TECHNICAL CHARACTERISTICS

Composition: Mixture of cement with mineral fillers and special additives

Amount of water for batching, ml / kg: 210-240

Time of using the mortar mixture, minutes : 60

Application temperature, ° С: from +10 to +30

Compressive strength after 28 days, MPa, not less than:  0,5

Surface Finishing : after 48 hours

Consumption, kg / m²: 2,5-2,6

GRAIN SIZE UP TO 1.5 MM

THIN-LAYER DECORATIVE FINISHING OF WALLS OUTSIDE AND INSIDE OF PREMISES

WHITE COLOR

VAPOR- PERMEABLE

CONVENIENT IN APPLICATION

DOES NOT BURN

ENVIRONMENTALLY PURE

Mixture “Artisan”  Ц.1.ШТ4

ДСТУ БВ.2.7-126:2011

Hygienic conclusion of the Ministry of Health of Ukraine.