APPLICATION

The waterproofing mixture is designed to protect the building structures from the effects of water inside and outside buildings, including for waterproofing roofs, basements, foundations, socles, parapets, balconies, terraces, showers, swimming pools, reservoirs intended for water storage, etc. Has good adhesion to metal, including colored. Do not apply to gypsum and anhydrite bases. The waterproofing mixture is applied from the side of the water. The elastic mixture with a layer thickness of 3 mm perceives deformations with a crack opening width of up to 0.8 mm. Protection against permanent wetting: 2 layers of lubricating waterproofing with a total thickness of 3.0 mm.

PREPARATION OF THE SURFACE

Waterproofing mixture should cover only dense, dry, clean base peeled from dust, dirt, grease, loose material. Small irregularities of the surface of the vertical bases should be smoothed out, and the unstable layer should be removed. Before applying waterproofing, the mineral substrate must be moistened, preventing the appearance of a continuous water film. From the metal surfaces to remove the oxide film, it is possible to treat the metal surface with a special metal primer. Cracks thicker than 0.8 mm thick should be repaired with repair mortar, small cracks can be sealed with a special tape, and this composition using a building mesh, etc. Waterproofing mixture is applied to the previously primed surface (concrete, cement-sand mixture, brickwork) after 28 days of the strength setting.

PERFORMANCE OF WORK

The dry mixture is gradually added to the liquid component – Artisan No. 11 emulsion with mixing in a ratio of 1 kg of the mixture to 320-350 ml of the liquid component, to obtain a homogeneous mixture without lumps. Stirring is performed by a low-speed mixer. After 5 minutes, the stirring is repeated. Use of a mortar mixture is possible for 30 minutes. Waterproofing applied for 2, and if necessary 3 passes. The prepared mortar mixture by a thin layer with a brush or spatula should be applied to a damp but not wet base. Each subsequent layer is applied to the already hardened, but not yet dried, the previous one, adhering to the “wet on wet” method. The applied layer must be protected from rapid drying. Each successive layer is applied perpendicular to the previous one. The temperature of the mixture is from +5 to +30 ° C. After 7 days, the coating is ready for use.

Note!

If necessary, when thickening, dilute the mixture with a liquid component; do not dilute the composition with water.

SAFETY PRECAUTIONS

The elastic waterproofing mixture contains cement, which at the time of hydration gives an alkaline reaction, therefore, during work, it is necessary to protect eyes and skin. In case of contact with the solution, rinse with water and, if necessary, seek the help of a doctor.

RECOMMENDATIONS

In addition to the information above on the use of elastic waterproofing mixture should be guided by the current regulatory documentation for the device of polymer waterproofing.

EXPIRATION DATE

In hermetically sealed packaging, the shelf life is 12 months from the date of manufacture indicated on the package. Do not allow the liquid component to freeze.

TECHNICAL CHARACTERISTICS

Composition: a mixture of cement with mineral aggregates and corrective additives and an aqueous dispersion of the polymer with additives

Mixing ratio, l / kg, approx.: 0,32 – 0,35

Time of use, min, not less than:  30

Application temperature, ° С:  from +5 to +30

Water resistance, for 24 hours, MPa, not less than:  0,2

Ability to overlap cracks, mm:  0,8

Strength of adhesion to the base, MPa, not less than:   0,5

Relative elongation,%, not less than:   8

Tensile strength, MPa:   0,6

Consumption

• dry component, kg / m² / mm thickness, not more than: – 1,4
• liquid, l / m² / mm thickness, about: – 0,46

LAYER THICKNESS TO 3 MM

WELL APPLIES WITH BRUSH AND SPATULA

WATERPROOF

ENVIRONMENTALLY PURE

Mixture “Artisan Ц.1.ГІ2

ДСТУ Б В.2.7-126:2011                    

Hygienic conclusion of the Ministry of Health of Ukraine.

APPLICATION

Thin-layer waterproofing is used to protect floors and walls from moisture in bathrooms, toilets and other household premises on well-prepared grounds.

PREPARATION OF THE SURFACE

Before applying a waterproofing mortar, it is necessary to perform a mechanical cleaning of the surface of old plaster and paint, clay and silt layers, oil and bitumen stains, etc. Surfaces must be primed before applying a waterproofing coating. (Due to the loss of moisture during the recruitment process, the waterproofing properties of the composition can be significantly reduced). Surplus water from horizontal surfaces should be removed. Otherwise, in the future, it is possible to peel off the waterproofing coating together with the weakened layer.

PERFORMANCE OF WORK

5 kg of a dry mix to mix with 1,25-1,4 l of water to reception of a homogeneous dense non-intercalating weight. The excess amount of water added to the mixture can reduce the performance of the waterproofing. Leave for 5 minutes, stir again. The solution is applied to the previously prepared surface with a hand tool (grater, construction brush). The thickness of the layer is 3-5 mm. The waterproofing solution is applied in two layers, the subsequent layer is applied after the drying of the first, perpendicular to each other.

Note!

To increase the degree of adhesion of the waterproofing mortar to the weakened surfaces to be treated and to reduce water absorption by the base material, it is recommended to pre-coat with primer “ARTISAN No. 7”. In special cases, it is recommended to lay the waterproofing layer on the plaster grid. The quantity of the prepared solution should correspond to the productivity of the work when laying the waterproofing solution of the required thickness and quality. Under normal conditions, it is necessary to use a freshly prepared solution for 30-40 minutes.  Freshly applied material should be periodically moistened with water or covered with a protective film in the initial time of hardening. It is especially important not to allow the drying of the material in hot weather and drafts during these periods.

All recommendations are valid at a temperature of + 20 ° C and a relative humidity of 60%. When carrying out work should be guided by building codes and regulations.

The manufacturer is not responsible for misuse of the material and its application in the manner and conditions other than those specified in these instructions.

SAFETY PRECAUTIONS

The mixture contains cement, which when combined with water forms alkali. Avoid contact with skin and mucous membranes. Be sure to work in rubber gloves. In case of contact with the skin and eyes, rinse thoroughly with water.

EXPIRATION DATE

In dry conditions and hermetic packaging the period of storage is at least 12 months from the date of manufacture.

                                                                                           PACKAGING             

The dry mix is packaged in bags of 5 kg.

TECHNICAL CHARACTERISTICS

Composition: mixture of cement, mineral fillers and special additives

The amount of water for mixing the mortar l/kg:  1,25-1,4/5

Time of use, min.:  60

Substrate temperature, ° С:  from +15 to +30

Ambient conditions temperature, ° С: not less than +10

Readiness for use, days: after 7 days

Consumption, kg / m2 / mm: 1,5

SUSTAINABLE TO SHRINKAGE

QUICK SET OF STRENGTH

GOOD ADHESION

WATERPROOF

ENVIRONMENTALLY PURE

Mixture “Artisan Ц.1.ГІ1

ДСТУ БВ.2.7-126:2011                     

Hygienic conclusion of the Ministry of Health of Ukraine.

APPLICATION

For waterproofing of walls of basements, buried and underground structures, sanitary facilities, swimming pools, balconies, open terraces and maintained roofs, as well as reservoirs, wells. The treated surfaces perceive a water pressure of at least 0.5 atmospheres; has good adhesion characteristics;

PREPARATION OF THE SURFACE

Before applying a waterproofing mortar, it is necessary to perform a mechanical cleaning of the surface from old plaster and paint, clay and silt layers, oil and bitumen stains, etc. Surfaces must be primed before applying a waterproofing coating. (Due to the loss of moisture during the recruitment process, the waterproofing properties of the composition can be significantly reduced). Surplus water from horizontal surfaces should be removed. Otherwise, in the future, it is possible to peel off the waterproofing coating together with the weakened layer.

PERFORMANCE OF WORK

25 kg of dry mixture mixed with 5.5 – 6.5 liters. water until a uniform thick, non-spreading mass is obtained. The excess amount of water added to the mixture can reduce the performance of the waterproofing. Leave for 5 minutes, stir again. The solution is applied to the previously prepared surface with a hand tool (grater, construction brush). The thickness of the layer is 3-5 mm. The waterproofing solution is applied in two layers, the subsequent layer is applied after the drying of the first, perpendicular to each other.

Note!

To increase the degree of adhesion of the waterproofing mortar to the weakened surfaces to be treated and to reduce water absorption by the base material, it is recommended to pre-treat with primer  ARTISAN No. 7. In special cases it is recommended to lay the waterproofing layer on the plaster grid. The quantity of the prepared solution should correspond to the productivity of the work when laying the waterproofing solution of the required thickness and quality. In normal conditions it is necessary to use a freshly prepared solution within 30-40 minutes. Freshly applied material should be periodically moistened with water or covered with a protective film in the initial time of hardening. It is especially important not to allow the drying of the material in hot weather and drafts during these periods.

All recommendations are valid at a temperature of + 20 ° C and a relative humidity of 60%. When carrying out work should be guided by building codes and regulations.

The manufacturer is not responsible for misuse of the material and its application in the manner and conditions other than those specified in these instructions.

SAFETY PRECAUTIONS

The mixture contains cement, which when combined with water forms alkali. Avoid contact with skin and mucous membranes. Be sure to work in rubber gloves. In case of contact with the skin and eyes, rinse thoroughly with water.

EXPIRATION DATE

In dry conditions and hermetic packaging the period of storage is at least 12 months from the date of manufacture.

                                                                                           PACKAGING             

The dry mix is packaged in bags of 25 kg.

TECHNICAL CHARACTERISTICS

Composition: mixture of cement, mineral fillers and special additives

The amount of water for mixing the mortar:  5,5-6,5 l/25 kg

Time of solution use, min.:  60

Compressive strength, MPa, not less than:   12

Water-resistant, MPa, not less than:  0,05

Recommended thickness, mm:   3-5

Consumption, kg / m2 / mm: 1,5

QUICK-HARDENING

DOES NOT HAVE A SHRINKAGE

FROST-RESISTANT

DOES NOT BURN

ENVIRONMENTALLY PURE

Mixture “Artisan”  Ц.1.ГІ1

ДСТУ БВ.2.7-126:2011                  

Hygienic conclusion of the Ministry of Health of Ukraine.