APPLICATION

Gypsum-perlite plaster is used in finishing works for manual plastering and leveling of walls and ceilings with any type of surface (concrete, gypsum, stone, brick, cellular-concrete) as well as for the preparation of grounds for painting, wallpaper, facing work inside rooms with normal humidity in residential, administrative and industrial buildings. Gypsum plaster allows you to get a smooth surface that does not require putty before the subsequent work. Has a short drying period. It does not form cracks and does not fade, even with a thick layer. Creates bases with improved heat and sound insulation properties for the most comfortable living conditions. In the rooms a favorable microclimate is formed.

Gypsum-perlite plaster – is a method of leveling walls, with the help of screed strips, which is the only effective alternative to gypsum boards. The main advantage – saving the volume of the internal space, as well as ease of repair and maintenance for long-term operation (gypsum cardboard systems should be dismantled). It is possible to apply plaster in the usual way, but the most qualitative result is obtained when performing work using screed strip.

PREPARATION OF THE SURFACE

The surface must be dry and firm, free of dust, oils, dirt and other contaminants of organic origin. To improve the adhesion of the solution to the substrate; for binding of dust residues; for highly absorbent and cementitious substrates – mandatory priming with “ARTISAN No. 7” deep penetration primer is required.

PREPARATION OF THE MORTAR

The dry plaster mixture is mixed with clean water until it is uniform. The mixture is poured into the water. The solution is held for 5-10 minutes, then mixed again. After that, the mixture is ready for use.

PERFORMANCE OF WORK

Plastering is carried out according to predetermined screed strips. The plaster solution is applied to the surface in one layer and leveled. The optimum layer thickness is 10 mm (the minimum is 5 mm, the maximum is 30 mm). After the beginning of setting, the surface is treated with a wide spatula, and after 15-20 minutes rubbed with a sponge grater, moistened with water and smooth with a metal spatula, obtaining an absolutely smooth surface. Plastering in two layers is allowed. For this, it is necessary to apply a notch on the first layer that has not yet hardened, and then apply the second on the dried surface of the first layer.

The manufacturer is not responsible for misuse of the material and its application in the manner and conditions other than those specified in these instructions.

SAFETY PRECAUTIONS

All components that make up the mixture are non-toxic and harmless to health. Work with the material in accordance with accepted standards.

EXPIRATION DATE

In dry conditions and hermetic packaging the period of storage is at least 12 months from the date of manufacture.

                                                                                           PACKAGING             

The dry mix is packaged in bags of 30 kg.

TECHNICAL CHARACTERISTICS

Composition: mineral raw materials with gypsum and special additives.

Amount of mixing water, l / kg: 0,35 – 0,5

Consumption, kg / m2 / mm:  1

Compressive strength, MPa, not less than: 1,5

Time of use, hours:   1

Optimum application temperature, ° С: from +10 to +30

RECOMMENDED LAYER THICKNESS – 10 MM

HIGH ADHESION

HIGH PLASTICITY

EASY TO USE

ENVIRONMENTALLY PURE

Mixture “Artisan Г.2.ШТ6

ДСТУ БВ.2.7-126:2011         

Hygienic conclusion of the Ministry of Health of Ukraine.

APPLICATION

Universal solution is used for construction and repair works as leveling plaster for seams between panels, walls, slits, openings, etc. It is successfully applied for leveling walls, ceilings, and also as a plaster solution. Thanks to special additives, the solution is highly plastic, has a high adhesion to almost any surface, and does not form cracks. Has a high thermal insulation quality.

PREPARATION OF THE SURFACE

The surface of the wall on which the plaster solution is applied should be pre-cleaned of grease, old paints, plaster exfoliations, loose substrates. All the grounds must be treated with a deep penetration primer TM “ARTISAN No. 7”, or primer TM “ARTISAN No. 8”, depending on the substrate.

PERFORMANCE OF WORK

To obtain the solution, it is necessary to mix 20 kg of dry product in 5.6-6.6 liters of water and mix thoroughly by mechanical means until a homogeneous paste-like composition is obtained. Allow the solution to stand for 5 minutes, and then mix again. The solution is applied to the prepared surface, with a thickness of no more than 30 mm. All recommendations are valid at a temperature of + 20 ° C and a relative humidity of 60%.

! Under adverse weather conditions (high temperature, wind, direct sunlight), the time of use of the solution which is deposited on the surface can be significantly reduced.

! When the temperature of use of the solution decreases, the setting time increases. When carrying out work should be guided by building codes and regulations.

The manufacturer is not liable for improper use of the material, nor for its use for purposes and conditions not provided for by the instruction.

SAFETY PRECAUTIONS

The mixture contains cement, which, when mixed with water, forms an alkali. Work should be in rubber gloves. If the solution gets into the skin or eyes, rinse them with plenty of water, if necessary, consult a doctor.

EXPIRATION DATE

In dry conditions and hermetic packaging the period of storage is at least 12 months from the date of manufacture.

PACKAGING

The dry mix is packaged in bags of 20 kg.

TECHNICAL CHARACTERISTICS

Composition: Mixture of cement with perlite, mineral fillers and special additives

The amount of water for mixing the solution 5.6-6.6 l / 20 kg: 5,5-6,6 l/20kg

Time of use, min, not less than: 60

Application temperature, ° С: from +10 to +30

Strength of adhesion to the substrate, MPa, not less than: 0,3

Compressive strength, MPa, not less than: 7,0

Coefficient of thermal conductivity, W / m * K, not more than: 0,3

Surface Finishing: after 48 hours

Consumption, kg / m2 / mm, not more than: 1,2

Mixture Artisan C.1.SHT2

DSTU BV.2.7-126: 2011

Hygienic conclusion of the Ministry of Health of Ukraine

LEVELS THE SURFACE OF CEILINGS AND WALLS (UP TO 30 MM)

LEVELING THE PANELS JOINTS

EASY TO USE

FROST-RESISTANT

DOES NOT BURN

ENVIRONMENTALLY FRIENDLY

HIGH HEAT INSULATING QUALITY