APPLICATION

Priming paint is designed for pre-treatment of bases as a strengthening, adhesive primer before applying subsequent textured, decorative coatings. It is applied on the bases of concrete, cement-sand, cement-lime plasters, bricks, plasterboard, etc. inside and outside buildings. It is also used in the system of external warming by wet method “Artisan” before applying decorative plaster. Can be used as an independent decorative layer. The primed base has the appearance of a white rough surface.

PREPARATION OF THE SURFACE

Preparation of the base is carried out, according to СНиП 3.04.01-87  and ДБН В.2.6-22-2001. The substrate must be dry, clean, without visible damage. Loose, unstable, porous surfaces are removed mechanically, aligned.

PERFORMANCE OF WORK

Stir well before use. The paint should be applied to the surface with a paint brush (do not apply with a roller). The work should be carried out at the temperature of the base from +5 to +30 ºС. Under normal climatic conditions (temperature +20 ° C and relative humidity 60%), the drying time is 4 hours. During application, as well as drying, freshly painted surfaces must be protected from rain, strong wind and direct sunlight until completely dry. Immediately after use, the instruments should be rinsed thoroughly with water, if necessary, cleaned with an organic solvent.

ATTENTION! Do not freeze the product. The manufacturer is not responsible for the incorrect use of the material, as well as for its use for purposes and conditions not provided for by the instruction.

SAFETY PRECAUTIONS

Do not apply primer paint to skin and mucous surfaces. It is advisable to work in rubber gloves. In case of contact with skin or eyes, rinse thoroughly with water.

EXPIRATION DATE

In original hermetic packaging and in cool conditions (not below +5 ° C and not above +30 ° C) 12 months from the date of manufacture indicated on the package. Avoid freezing.

PACKAGING

The paint is packed in plastic buckets of 7.5 and 15 kg.

UTILIZATION

Unused residues should be allowed to dry and disposed of with household rubbish.

TECHNICAL CHARACTERISTICS

Composition: mixture of pigments and fillers in aqueous polymer dispersions

Drying time, hour.: from 3 to 6

Appearance of the painted surface: matt milky white

Density :  1,58 – 1,65 kg / l

Application temperature :  from +5 °С to +30 °С

Consumption, kg / m2 : 0,35  – 0,4

POLYMER

STRENGTHENS WEAK SURFACES

INCREASES ADHESION TO VARIOUS BASES

HIGH COATING CAPACITY

VAPOR-PERMEABLE

WATERPROOF

ECOLOGICALY CLEAN

ТУ У В.2.7-24.3–30554583-004-2002

Hygienic conclusion of the Ministry of Health of Ukraine.

PERFORMANCE OF WORK

With the primer cover a dense, load-bearing, dry, hygroscopic bases, cleaned of impurities. Dilute the soil concentrate in a ratio of 1 to 6 with clean water and mix thoroughly by hand, or by drill with a nozzle at low speed. The resulting solution is applied by a paint brush with a uniform layer, a special product formula allows the surface to be treated in a single layer. Drying time of the dispersion on the basis of 4 hours, at a temperature of 20 ° C.

SAFETY PRECAUTIONS

It is necessary to avoid getting the dispersion on the skin and mucous surfaces. It is advisable to work in rubber gloves. In case of dispersion on the skin or eyes, they must be thoroughly rinsed.

EXPIRATION DATE

In a sealed container in a cool place for up to 12 months. Protect from frost.

PACKAGING

Dispersion is packaged in 2, 5, 10 liters.

TECHNICAL CHARACTERISTICS

Composition: acryl-styrene dispersion

Color:  milky white liquid

Density           : 1040  kg/m³

Temperature of execution of works:  from +10 to +30 °С

Consumption:  from 0,1  to 0,2  l/m²

ECONOMICAL

VAPOR-PERMEABLE

ECOLOGICALLY CLEAN

HYDROPHOBIZATED

INCREASES ADHESION OF NEXT LAYERS

STRENGTHENS AND PROSPECTS THE FOUNDATION

TABLE

Foundation	Proportion of breeding, parts	Quantity of the mortar, liters	Coverage area, sq.m.
Weakly absorbing (concrete)	1:9	20	100
Normally absorbent (plaster, GKL)	1:8	18	90
Powder-absorbing (foam-aerated concrete)	1:6	14	70

ТУ У В.2.7-24.3–30554583-004-2002

Hygienic conclusion of the Ministry of Health of Ukraine

]]> https://artisan.ua/product/primer-concentrate-N-16/feed/ 0 https://artisan.ua/product/betoncontact-n15/ https://artisan.ua/product/betoncontact-n15/#respond Sat, 11 Nov 2017 12:38:10 +0000 https://artisan.ua/?post_type=product&p=503 Betoncontact  №15 primer with quartz filler  increases the adhesion to the foundation]]> Betoncontact  №15 primer with quartz filler  increases the adhesion to the foundation

APPLICATION

 Primer uses for pre-treatment not absorbent bases (monolithic concrete, massive concrete coatings, polished concrete mounting blocks, sand-lime brick, etc.) and foundations with high water absorption (cellular concrete, etc.) before applying gypsum, lime, lime-cement, cement and other plasters, adhesives compositions, as well as before applying gypsum boards. Used as adhesive and reinforcing primers. Can also be used in the system of external insulation wet sanded before applying the decorative plaster.

PREPARATION OF THE SURFACE

Substrate preparation is carried out according to normative documents. With primer “Betoncontact” are covered dense, dry, clean grounds, cleaned of dust, dirt, grease, and loose elements. Loose, flaking surfaces are removed with a brush.

PERFORMANCE OF WORK

Tool is ready to use. Before applying necessarily stir. Primer “Betoncontact” applies on the surface using a paint brush. Under normal climatic conditions  (temperature +20 °С and relative humidity 60%) drying time of primer on the basics – from 3 to 6 hours, very thick base withstands up to two days. Work should be carried out at temperature of base from +5 to +30 °С.

 ATTENTION! Freezing of the product is not allowed. The manufacturer is not responsible for incorrect material use, and also, for use of it for purposes and conditions not set in the instruction.

SAFETY PRECAUTIONS

You should avoid getting a primer on the skin and mucous membranes. You must work in rubber gloves. In case of contact with skin and eyes, you must wash out it thoroughly with running water.

EXPIRATION DATE

In brand sealed packaging in cool conditions (not lower +5 °С and not higher +30 °С) 12 months from the date of manufacture indicated on the package.

PACKAGING

The product is packaged per 3, 7,5 and 15 kg.

TECHNICAL CHARACTERISTICS

Composition: a mixture of pigments and fillers in water polymer dispersions

Drying time: from 3 to 6 hours

Color:  light beige

Density                : about 1,59 kg/l

Temperature of execution of works:  from +5 to +30 °С

Consumption:  from 0,25 to 0,5 kg/m²

FOR SMOOTH FOUNDATIONS:

• MONOLITHIC CONCRETE
• GLASS
• CERAMIC TILES

FOR STRONGLY ABSORBING FOUNDATIONS:

• FOAM CONCRETE
• WOODEN FOUNDATIONS
• SILICATE AND CERAMIC BRICK

ТУ У В.2.7-24.3-30554583-004-2002

Hygienic conclusion of the Ministry of Health of Ukraine

APPLICATION

The primer is used for pretreatment of porous, weak, strong-absorbing substrates (lightweight concrete, plaster, gypsum and brick surfaces), increasing adhesion to the substrate. Small primer particles (0,04-0,07 mm), have a strong penetration into the base, and reliably close the pores. Increases adhesion, prevents the formation of fungi and mold under the coating layer.

PREPARATION OF THE SURFACE

Preparation of the base is carried out, according to СНиП 3.04.01-87 and ДБН В.2.6-22-2001. The substrate must be dry and strong, without visible damage. Unstable, loose areas of the surface of the base are cleaned with a brush.

!! Do not use on surfaces that are not reliably isolated from groundwater. Otherwise, the penetration of ground moisture will be a source of permanent fading and the appearance of highs.

PERFORMANCE OF WORK

Primer is applied to the base with a paint brush. Bases with a large absorbing capacity, it is necessary to cover 2-3 times.

The manufacturer shall not be liable for improper use of the material, nor for its use for purposes and conditions not provided for by the instruction.

SAFETY PRECAUTIONS

Avoid contact with skin and mucous membranes. It is advisable to work in rubber gloves. In case of contact with the skin and eyes, rinse thoroughly with running water.

EXPIRATION DATE

In a sealed container up to 12 months. Protect from frost.

PACKAGING

The primer is packaged in cans of 5 and 10 liters.

TECHNICAL CHARACTERISTICS

Composition:  aqueous polymer dispersion with special additives

Drying time: from 3 to 6 hours

Appearance: milky white liquid, transparent after drying

Density: around  1 kg/l

Working temperature: from +5 to +30°С

Consumption: from 0,1 to 0,45 l/m2

HAS GOOD PENETRATION CAPACITY

INCREASES ADHESION

TRANSPARENT AFTER DRYING

RESISTANT TO ALKALIS INFLUENCE

VAPOR-PERMEABLE

ECOLOGICALLY CLEAN

ТУ У В.2.7-24.3–30554583-004-2002

Hygienic conclusion of the Ministry of Health of Ukraine.

PREPARATION OF THE SURFACE

Preparation of the base is carried out, according to СНиП 3.04.01-87 and ДБН В.2.6-22-2001. The basis has to be dry, clean, without visible damage.

PERFORMANCE OF WORK

Primer is applied to the substrate with the help of brush, roller or spray. Fundamentals with a high absorption capacity, it is necessary to cover 2-3 times.

The manufacturer is not liable for improper use of the material, or for its use for purposes and conditions not provided for by the instruction.

SAFETY PRECAUTIONS

It is necessary to observe safety precautions in the manufacture of construction works.

EXPIRATION DATE

In a sealed container it is up to 12 months. Protect from frost.

PACKAGING

The primer is packaged in cans of 2, 5, 10 liters.

TECHNICAL CHARACTERISTICS

Composition: aqueous polymer dispersion with special additives

Drying time: from 3 to 6 hours

Appearance: milky white liquid, transparent after drying

Density: around  1 kg/l

Working temperature: from +5 to +30°С

Consumption: from 0,1 to 0,4 l/m2

POLYMER

STRENGTHENS WEAKLY BASES

INCREASES ADHESION TO VARIETY BASIS

SIMPLIFIED PROCESS OF APPLICATION OF DECORATIVE PLASTER

HIGH COVERING ABILITY

vapor-permeable

ECOLOGICALLY CLEAN

WATERPROOF

TU U В.2.7-24.3–30554583-004-2002

Hygienic conclusion of the Ministry of Health of Ukraine

APPLICATION

Primer for deep penetration, with a high content of binder polymer, is used for the surface treatment of concrete, brick, cement-sand plaster, gypsum board, before laying parquet, ceramic tile, painting, wallpapering and plastering. To strengthen the layers prone to flowability and loosening, increase the adhesion of cellular concrete, gypsum boards, monolithic floors, hygroscopic plasters and other surfaces. The applied primer layer after drying becomes transparent, colorless, equalizes the absorbing capacity of the surface and reduces the application of paint, varnish, water dispersion and plaster compositions. Can be used as an additive in solutions to increase their plasticity, adhesion, strength and moisture resistance. It is designed for all types of work at sites, with increased sanitary and technical requirements. Do not contain solvents and plasticizers, which are the source of the release of volatile organic compounds into the environment (VOCs). Does not adversely affect the quality of air inside freshly treated rooms.

PREPARATION OF THE SURFACE

Preparation of the base is carried out, according to СНиП 3.04.01-87 and ДБН В.2.6-22-2001. The substrate must be dry, clean, without visible damage. Loose, fragile surfaces are cleaned with a brush.

PERFORMANCE OF WORK

The primer is applied to the substrate with a paintbrush, roller, etc. Fundamentals with a large absorbing capacity, it is necessary to cover 2-3 times. The manufacturer is not responsible for improper use of the material, as well as its application in order and conditions not stipulated by the instruction.

SAFETY PRECAUTIONS

Avoid contact with skin and mucous membranes. It is advisable to work in rubber gloves. In case of contact with the skin and eyes, rinse thoroughly with running water.

EXPIRATION DATE

In a sealed container up to 12 months. Protect from frost.

PACKAGING

The primer is packaged in cans of 2 liters, 5 liters, 10 liters.

TECHNICAL CHARACTERISTICS

Composition: polymer dispersion with an increased content of water-based binders and special additives

рН:  6-9

Drying time, hour, up to: Up to 4 hours

Vapor permeability:  not less than 0.05 g / m2h-Pa

Density:  about 1 kg / l

Binding ability: not less than 6 g

Film resistance to static water impact: not less than 24 hours

Depth of penetration depending on substrate density:  2-4 mm

Working temperature:  from +5°С to +30 °С

Consumption: from 0,1 to 0,25 l / m²

Appearance: a mixture of milk color

Stability in storage : stable

STRENGTHENS THE FOUNDATION

INCREASES ADHESION

TRANSPARENT AFTER DRYING

HAS GOOD PERCENTAGE CAPACITY

ECOLOGICALLY CLEAN

The hygienic conclusion of the Ministry of Health of Poland НК/В/1329-1301/2015 as of 4.01.2016