The mixture is intended for fastening ceramic, concrete, clinker tiles, as well as tiles made of artificial granite, tiles, mosaics with a size of no more than 600×600 mm on walls and floors with a high heating temperature (up to 180 °C) indoors and outdoors. For strong brick, cement-sand, cement-lime, concrete and other mineral surfaces, it is especially recommended for facing fireplaces, stoves, warm floors (water and electric).

PREPARATION OF THE BASE

The foundation is prepared in accordance with DSTU – N B A.3.1-23:2013 and DSTU B V.2.6-212:2016. The base must be completely dry and strong. If there are irregularities or protrusions on the base, they should be removed by grinding or sandblasting followed by dust removal from the crevices with a vacuum cleaner. To remove oil, grease, wax, paraffin, paints and other impurities from the surface of the base, it is necessary to use alkaline solutions, and then wash with water. Large damages, for example, chipped parts of the screed, cracks or voids, must be removed and filled. Before applying the adhesive solution, the mineral base with a medium or high degree of water absorption must be treated with one of the deep penetration soils ARTISAN #7, #17 or #8. If the surface is high-strength, dense (concrete, reinforced concrete construction, silicate brick), ARTISAN CONCRETE CONTACT No. 15 is recommended to increase adhesion.

APPLICATION METHOD

Pour the adhesive mixture into a container with clean water (+18 – +20°С), using approximately 5.5-6.0 liters of water per 25 kg of the mixture, and knead the solution to a homogeneous consistency without lumps. Allow the solution to settle for 3-5 minutes and mix again. The resulting mixture is applied in a thin layer of up to 10 mm on the prepared surface using a toothed spatula with square teeth (tooth size 6-10 mm), depending on the size of the tile. The tile is not pre-wetted. Lay on the solution and press it to the base, if necessary, tap it with a rubber hammer so that the adhesive mixture is in contact with at least 80% of the surface area of the tile. The tile position can be adjusted within 10 minutes. After 48 hours, the surface is ready for technological movement, you can fill the seams with grout. Warm-up of the lined base should be carried out after the adhesive solution has fully hardened and spread (28 days). Increase the base temperature gradually.

NOTE!!! The most effective result is achieved at t+20°C and relative air humidity of 60%. Under other conditions, the operating parameters may change. Use only as intended.

EXPIRATION DATE

In dry conditions and sealed packaging, 12 months from the date of manufacture indicated on the packaging.

SAFETY TECHNOLOGY

The mixture contains cement, which, when combined with water, forms an alkali. It is advisable to work in rubber gloves. In case of liquid contact with skin and eyes, it is necessary to rinse thoroughly with running water. The material is non-flammable and explosive.

PACKAGING

The dry mixture is packaged in 25 kg bags.

SPECIFICATIONS

Component: a mixture of cement with mineral fillers and special additives
Optimum temperature for performance of work, °C from +5 to +30
Shelf life of the solution, min. 60
Open time, min., not less than 20
Adjustment time, min., not less than 10
Technological movement, hours, no earlier than 48
Adhesion strength to the base, MPa, not less than 0.8
Temperature of use, °С up to 180
Thermal conductivity, W/(m-K), no more than 0.3
Water consumption, l/kg 0.22-0.24
Solution consumption, kg/m2 1.5

Mix “Artisan” Ts.1.3K2 DSTU BV.2.7-126:2011

Hygienic conclusion of the Ministry of Health of Ukraine.

APPLICATION

The waterproofing mixture is designed to protect the building structures from the effects of water inside and outside buildings, including for waterproofing roofs, basements, foundations, socles, parapets, balconies, terraces, showers, swimming pools, reservoirs intended for water storage, etc. Has good adhesion to metal, including colored. Do not apply to gypsum and anhydrite bases. The waterproofing mixture is applied from the side of the water. The elastic mixture with a layer thickness of 3 mm perceives deformations with a crack opening width of up to 0.8 mm. Protection against permanent wetting: 2 layers of lubricating waterproofing with a total thickness of 3.0 mm.

PREPARATION OF THE SURFACE

Waterproofing mixture should cover only dense, dry, clean base peeled from dust, dirt, grease, loose material. Small irregularities of the surface of the vertical bases should be smoothed out, and the unstable layer should be removed. Before applying waterproofing, the mineral substrate must be moistened, preventing the appearance of a continuous water film. From the metal surfaces to remove the oxide film, it is possible to treat the metal surface with a special metal primer. Cracks thicker than 0.8 mm thick should be repaired with repair mortar, small cracks can be sealed with a special tape, and this composition using a building mesh, etc. Waterproofing mixture is applied to the previously primed surface (concrete, cement-sand mixture, brickwork) after 28 days of the strength setting.

PERFORMANCE OF WORK

The dry mixture is gradually added to the liquid component – Artisan No. 11 emulsion with mixing in a ratio of 1 kg of the mixture to 320-350 ml of the liquid component, to obtain a homogeneous mixture without lumps. Stirring is performed by a low-speed mixer. After 5 minutes, the stirring is repeated. Use of a mortar mixture is possible for 30 minutes. Waterproofing applied for 2, and if necessary 3 passes. The prepared mortar mixture by a thin layer with a brush or spatula should be applied to a damp but not wet base. Each subsequent layer is applied to the already hardened, but not yet dried, the previous one, adhering to the “wet on wet” method. The applied layer must be protected from rapid drying. Each successive layer is applied perpendicular to the previous one. The temperature of the mixture is from +5 to +30 ° C. After 7 days, the coating is ready for use.

Note!

If necessary, when thickening, dilute the mixture with a liquid component; do not dilute the composition with water.

SAFETY PRECAUTIONS

The elastic waterproofing mixture contains cement, which at the time of hydration gives an alkaline reaction, therefore, during work, it is necessary to protect eyes and skin. In case of contact with the solution, rinse with water and, if necessary, seek the help of a doctor.

RECOMMENDATIONS

In addition to the information above on the use of elastic waterproofing mixture should be guided by the current regulatory documentation for the device of polymer waterproofing.

EXPIRATION DATE

In hermetically sealed packaging, the shelf life is 12 months from the date of manufacture indicated on the package. Do not allow the liquid component to freeze.

TECHNICAL CHARACTERISTICS

Composition: a mixture of cement with mineral aggregates and corrective additives and an aqueous dispersion of the polymer with additives

Mixing ratio, l / kg, approx.: 0,32 – 0,35

Time of use, min, not less than:  30

Application temperature, ° С:  from +5 to +30

Water resistance, for 24 hours, MPa, not less than:  0,2

Ability to overlap cracks, mm:  0,8

Strength of adhesion to the base, MPa, not less than:   0,5

Relative elongation,%, not less than:   8

Tensile strength, MPa:   0,6

Consumption

• dry component, kg / m² / mm thickness, not more than: – 1,4
• liquid, l / m² / mm thickness, about: – 0,46

LAYER THICKNESS TO 3 MM

WELL APPLIES WITH BRUSH AND SPATULA

WATERPROOF

ENVIRONMENTALLY PURE

Mixture “Artisan Ц.1.ГІ2

ДСТУ Б В.2.7-126:2011                    

Hygienic conclusion of the Ministry of Health of Ukraine.

APPLICATION

Thin-layer waterproofing is used to protect floors and walls from moisture in bathrooms, toilets and other household premises on well-prepared grounds.

PREPARATION OF THE SURFACE

Before applying a waterproofing mortar, it is necessary to perform a mechanical cleaning of the surface of old plaster and paint, clay and silt layers, oil and bitumen stains, etc. Surfaces must be primed before applying a waterproofing coating. (Due to the loss of moisture during the recruitment process, the waterproofing properties of the composition can be significantly reduced). Surplus water from horizontal surfaces should be removed. Otherwise, in the future, it is possible to peel off the waterproofing coating together with the weakened layer.

PERFORMANCE OF WORK

5 kg of a dry mix to mix with 1,25-1,4 l of water to reception of a homogeneous dense non-intercalating weight. The excess amount of water added to the mixture can reduce the performance of the waterproofing. Leave for 5 minutes, stir again. The solution is applied to the previously prepared surface with a hand tool (grater, construction brush). The thickness of the layer is 3-5 mm. The waterproofing solution is applied in two layers, the subsequent layer is applied after the drying of the first, perpendicular to each other.

Note!

To increase the degree of adhesion of the waterproofing mortar to the weakened surfaces to be treated and to reduce water absorption by the base material, it is recommended to pre-coat with primer “ARTISAN No. 7”. In special cases, it is recommended to lay the waterproofing layer on the plaster grid. The quantity of the prepared solution should correspond to the productivity of the work when laying the waterproofing solution of the required thickness and quality. Under normal conditions, it is necessary to use a freshly prepared solution for 30-40 minutes.  Freshly applied material should be periodically moistened with water or covered with a protective film in the initial time of hardening. It is especially important not to allow the drying of the material in hot weather and drafts during these periods.

All recommendations are valid at a temperature of + 20 ° C and a relative humidity of 60%. When carrying out work should be guided by building codes and regulations.

The manufacturer is not responsible for misuse of the material and its application in the manner and conditions other than those specified in these instructions.

SAFETY PRECAUTIONS

The mixture contains cement, which when combined with water forms alkali. Avoid contact with skin and mucous membranes. Be sure to work in rubber gloves. In case of contact with the skin and eyes, rinse thoroughly with water.

EXPIRATION DATE

In dry conditions and hermetic packaging the period of storage is at least 12 months from the date of manufacture.

                                                                                           PACKAGING             

The dry mix is packaged in bags of 5 kg.

TECHNICAL CHARACTERISTICS

Composition: mixture of cement, mineral fillers and special additives

The amount of water for mixing the mortar l/kg:  1,25-1,4/5

Time of use, min.:  60

Substrate temperature, ° С:  from +15 to +30

Ambient conditions temperature, ° С: not less than +10

Readiness for use, days: after 7 days

Consumption, kg / m2 / mm: 1,5

SUSTAINABLE TO SHRINKAGE

QUICK SET OF STRENGTH

GOOD ADHESION

WATERPROOF

ENVIRONMENTALLY PURE

Mixture “Artisan Ц.1.ГІ1

ДСТУ БВ.2.7-126:2011                     

Hygienic conclusion of the Ministry of Health of Ukraine.

APPLICATION

For waterproofing of walls of basements, buried and underground structures, sanitary facilities, swimming pools, balconies, open terraces and maintained roofs, as well as reservoirs, wells. The treated surfaces perceive a water pressure of at least 0.5 atmospheres; has good adhesion characteristics;

PREPARATION OF THE SURFACE

Before applying a waterproofing mortar, it is necessary to perform a mechanical cleaning of the surface from old plaster and paint, clay and silt layers, oil and bitumen stains, etc. Surfaces must be primed before applying a waterproofing coating. (Due to the loss of moisture during the recruitment process, the waterproofing properties of the composition can be significantly reduced). Surplus water from horizontal surfaces should be removed. Otherwise, in the future, it is possible to peel off the waterproofing coating together with the weakened layer.

PERFORMANCE OF WORK

25 kg of dry mixture mixed with 5.5 – 6.5 liters. water until a uniform thick, non-spreading mass is obtained. The excess amount of water added to the mixture can reduce the performance of the waterproofing. Leave for 5 minutes, stir again. The solution is applied to the previously prepared surface with a hand tool (grater, construction brush). The thickness of the layer is 3-5 mm. The waterproofing solution is applied in two layers, the subsequent layer is applied after the drying of the first, perpendicular to each other.

Note!

To increase the degree of adhesion of the waterproofing mortar to the weakened surfaces to be treated and to reduce water absorption by the base material, it is recommended to pre-treat with primer  ARTISAN No. 7. In special cases it is recommended to lay the waterproofing layer on the plaster grid. The quantity of the prepared solution should correspond to the productivity of the work when laying the waterproofing solution of the required thickness and quality. In normal conditions it is necessary to use a freshly prepared solution within 30-40 minutes. Freshly applied material should be periodically moistened with water or covered with a protective film in the initial time of hardening. It is especially important not to allow the drying of the material in hot weather and drafts during these periods.

All recommendations are valid at a temperature of + 20 ° C and a relative humidity of 60%. When carrying out work should be guided by building codes and regulations.

The manufacturer is not responsible for misuse of the material and its application in the manner and conditions other than those specified in these instructions.

SAFETY PRECAUTIONS

The mixture contains cement, which when combined with water forms alkali. Avoid contact with skin and mucous membranes. Be sure to work in rubber gloves. In case of contact with the skin and eyes, rinse thoroughly with water.

EXPIRATION DATE

In dry conditions and hermetic packaging the period of storage is at least 12 months from the date of manufacture.

                                                                                           PACKAGING             

The dry mix is packaged in bags of 25 kg.

TECHNICAL CHARACTERISTICS

Composition: mixture of cement, mineral fillers and special additives

The amount of water for mixing the mortar:  5,5-6,5 l/25 kg

Time of solution use, min.:  60

Compressive strength, MPa, not less than:   12

Water-resistant, MPa, not less than:  0,05

Recommended thickness, mm:   3-5

Consumption, kg / m2 / mm: 1,5

QUICK-HARDENING

DOES NOT HAVE A SHRINKAGE

FROST-RESISTANT

DOES NOT BURN

ENVIRONMENTALLY PURE

Mixture “Artisan”  Ц.1.ГІ1

ДСТУ БВ.2.7-126:2011                  

Hygienic conclusion of the Ministry of Health of Ukraine.

APPLICATION

Gypsum-perlite plaster is used in finishing works for manual plastering and leveling of walls and ceilings with any type of surface (concrete, gypsum, stone, brick, cellular-concrete) as well as for the preparation of grounds for painting, wallpaper, facing work inside rooms with normal humidity in residential, administrative and industrial buildings. Gypsum plaster allows you to get a smooth surface that does not require putty before the subsequent work. Has a short drying period. It does not form cracks and does not fade, even with a thick layer. Creates bases with improved heat and sound insulation properties for the most comfortable living conditions. In the rooms a favorable microclimate is formed.

Gypsum-perlite plaster – is a method of leveling walls, with the help of screed strips, which is the only effective alternative to gypsum boards. The main advantage – saving the volume of the internal space, as well as ease of repair and maintenance for long-term operation (gypsum cardboard systems should be dismantled). It is possible to apply plaster in the usual way, but the most qualitative result is obtained when performing work using screed strip.

PREPARATION OF THE SURFACE

The surface must be dry and firm, free of dust, oils, dirt and other contaminants of organic origin. To improve the adhesion of the solution to the substrate; for binding of dust residues; for highly absorbent and cementitious substrates – mandatory priming with “ARTISAN No. 7” deep penetration primer is required.

PREPARATION OF THE MORTAR

The dry plaster mixture is mixed with clean water until it is uniform. The mixture is poured into the water. The solution is held for 5-10 minutes, then mixed again. After that, the mixture is ready for use.

PERFORMANCE OF WORK

Plastering is carried out according to predetermined screed strips. The plaster solution is applied to the surface in one layer and leveled. The optimum layer thickness is 10 mm (the minimum is 5 mm, the maximum is 30 mm). After the beginning of setting, the surface is treated with a wide spatula, and after 15-20 minutes rubbed with a sponge grater, moistened with water and smooth with a metal spatula, obtaining an absolutely smooth surface. Plastering in two layers is allowed. For this, it is necessary to apply a notch on the first layer that has not yet hardened, and then apply the second on the dried surface of the first layer.

The manufacturer is not responsible for misuse of the material and its application in the manner and conditions other than those specified in these instructions.

SAFETY PRECAUTIONS

All components that make up the mixture are non-toxic and harmless to health. Work with the material in accordance with accepted standards.

EXPIRATION DATE

In dry conditions and hermetic packaging the period of storage is at least 12 months from the date of manufacture.

                                                                                           PACKAGING             

The dry mix is packaged in bags of 30 kg.

TECHNICAL CHARACTERISTICS

Composition: mineral raw materials with gypsum and special additives.

Amount of mixing water, l / kg: 0,35 – 0,5

Consumption, kg / m2 / mm:  1

Compressive strength, MPa, not less than: 1,5

Time of use, hours:   1

Optimum application temperature, ° С: from +10 to +30

RECOMMENDED LAYER THICKNESS – 10 MM

HIGH ADHESION

HIGH PLASTICITY

EASY TO USE

ENVIRONMENTALLY PURE

Mixture “Artisan Г.2.ШТ6

ДСТУ БВ.2.7-126:2011         

Hygienic conclusion of the Ministry of Health of Ukraine.

APPLICATION

Plaster “Mechanics” is used for plastering walls and ceilings with interior decoration of premises. It is applied to all standard mineral substrates either manually or mechanically.

PREPARATION OF THE SURFACE

The surface should be dry and durable, free from grease, old paints, crumbling plaster. To ensure high-quality and long-term exploitation, it is recommended to prime all grounds with primer  “Artisan No. 7” , or “Artisan No. 8 Super”, depending on the requirements to the substrate.

PERFORMANCE OF WORK

When plaster is applied mechanically, the dry mix is mixed with water in the installation, in a continuous automatic mode. The water supply to the plaster station should be adjusted in accordance with the consistency. Apply the plaster by spraying and leveling. In the event of a break in operation for more than 15 minutes, the machine should be cleaned with water. The hardened solution can only be removed mechanically. The average layer thickness is 15 mm (min 10 mm). Plastering in two layers is allowed. At the end of the work, immediately flush the tool and the plaster station.

The manufacturer is not responsible for misuse of the material and its application in the manner and conditions other than those specified in these instructions.

SAFETY PRECAUTIONS

All components that make up the mixture are non-toxic and harmless to health. Work with the material in accordance with accepted standards.

EXPIRATION DATE

In dry conditions and hermetic packaging the period of storage is at least 12 months from the date of manufacture.

PACKAGING

The dry mix is packaged in bags of 30 kg.

TECHNICAL CHARACTERISTICS

Composition: mixture of gypsum, mineral fillers and special additives

Amount of mixing water for manual application method, l / kg:  0,35 – 0,45

Time of use of the solution for manual application, mm, not less than:  60

Time of use, min, not less than: 60

Optimum temperature for solution use, ° С: from +5 to +30

Maximum layer thickness per application, mm:  30

Compressive strength, MPa, not less than:  2,0

Consumption for layer thickness 10 mm, kg / m2:  9-10

Thickness of a layer in one pass:

• min-10 mm
• -30 mm

Drying: in 7 days

Rotor-stator (PFT): D6-3

Water consumption:  650 l./hour

Hose Diameter:  25 mm.

MAXIMUM LAYER THICKNESS 30 MM

HIGH-PLASTIC

WHITE SMOOTH SURFACE

EASY TO USE

DOES NOT BURN

ENVIRONMENTALLY PURE

Mixture “Artisan”  Г.2.ШТ6

ДСТУ БВ.2.7-126:2011         

Hygienic conclusion of the Ministry of Health of Ukraine.

APPLICATION

Glue GS-62 is used for gluing to the solid bases of gypsum boards, combined gypsum panels. It can also be used for gluing stucco molding, gypsum blocks.

PREPARATION OF THE SURFACE

The surface of the wall on which the plaster solution is applied should be pre-cleaned of grease, old paints, plaster exfoliation, loose substrates. All the grounds must be treated with the primer “ARTISAN No. 7” or “ARTISAN No. 8”, depending on the substrate. With ground unevenness of more than 2 cm, the surface is leveled using gypsum boards (10 cm wide), which are glued to the GS-62 glue.

PERFORMANCE OF WORK

To obtain a solution, the dry mixture is poured into a container of water, at room temperature, thoroughly mixed until a uniform composition and the desired consistency are obtained and after 5 minutes it is re-mixed. Work with the solution should be with a clean tool made of stainless steel or plastic. Do not wet the base! If the surface is flat or leveled by means of strips, the solution is applied to the sheets of gypsum board with a notched trowel with continuous longitudinal strips and along the perimeter. At unevennesses of more than 2 cm, the HS-62 glue is applied with flat cakes along the edge of the gypsum board with an interval of 35 cm and along the perimeter with a minimum interval (almost complete). The installed panel is tightly pressed to the base and with light shocks through the rail is set according to the level. All recommendations are valid at a temperature of + 20 ° C and a relative humidity of 60%.

When carrying out work should be guided by building codes and regulations.

The manufacturer is not responsible for misuse of the material and its application in the manner and conditions other than those specified in these instructions.

SAFETY PRECAUTIONS

All components that make up the mixture are non-toxic and harmless to health. Work with the material in accordance with accepted standards.

EXPIRATION DATE

In dry conditions and hermetic packaging the period of storage is at least 12 months from the date of manufacture.

PACKAGING

The dry mix is packaged in bags of 15 and 30 kg.

TECHNICAL CHARACTERISTICS

Composition: mixture of gypsum, mineral fillers and special additives

Amount of water for mixing the mortar, l / kg: 0,34 – 0,43

Time of use: at t 20 ° C – 30 minutes

Temperature of use:  from +10 to +30

Peel strength, MPa, not less than:  0,5

Consumption, kg / m² / mm, up to:  1,2

MAXIMUM LAYER THICKNESS 30 MM

HIGH-PLASTIC

WHITE SMOOTH SURFACE

EASY TO USE

DOES NOT BURN

ENVIRONMENTALLY PURE

Mixture “Artisan”  Г.2.3К6

ДСТУ БВ.2.7-126:2011         

Hygienic conclusion of the Ministry of Health of Ukraine.

APPLICATION

The solution is used for manufacturing self-leveling floors (interlayers) on almost any pre-prepared basis in residential and public buildings. The thickness of the layer is 5-20 mm. Pouring into one layer. The ready-made screed meets all the requirements for floor interlayers, which can be applied to all types of coatings (parquet, linoleum, carpet coatings, tiles, paint, etc.)

PREPARATION OF THE SURFACE

The most important factor is the preparation of the substrate. The main requirement is that the substrate should be strong and clean (cementitious grounds – at least 28 days). Before applying floors from the base, it is necessary to remove not only coarse dirt, but even dust, preferably with a vacuum cleaner. Large damages, for example, broken parts of the screed or voids should be filled with putty. All the grounds must be primed with primer Artisan No. 7, or Artisan No. 8 super, depending on the requirements for the substrate. Do not wet the surface of the substrate.

PERFORMANCE OF WORK

The mixture is mixed with water with a low-speed stirrer until a homogeneous mass without lumps is obtained. Wait 5 minutes and mix again. Then pour the solution onto a prepared base and distribute it with a roller, a hard broom, a rubber straps and similar tools. It is recommended to roll the surface of the poured layer with a spiked roller to remove air lock. You can use a piston or auger pump to feed the solution. In the event of a break in operation for more than 20 minutes, the machine should be cleaned with water. The hardened solution can only be removed mechanically.

NOTE!

Excess water reduces the mechanical strength of the solution and leads to delamination. After 36 hours on the floor you can walk. It is possible to apply various coatings to the floor surface in 7-28 days, taking into account the requirements of the state building norms B.2.6-22-2001. The most effective result is achieved at t + 20 ° C and 60% relative humidity. In other conditions, the operating parameters of the mixture may vary. The manufacturer is not responsible for the incorrect use of the material, nor for application of it for purposes and conditions not provided for by the instruction.

SAFETY PRECAUTIONS

The mixture contains cement, which when combined with water forms alkali. It is necessary to prevent the hitting impregnation on the skin and mucous membranes. All work should be carried out in goggles, rubber gloves and protective clothing. Provide fresh air. In case of contact with skin or eyes, rinse thoroughly with water and if necessary, consult a doctor.

EXPIRATION DATE

In dry conditions and hermetic packaging the period of storage is at least 12 months from the date of manufacture.

PACKAGING

The dry mix is packaged in bags of 25 kg.

TECHNICAL CHARACTERISTICS

Composition: mixture of cement with mineral fillers and special additives

Quantity of water for solution preparation, l / kg :  0,22-0,24

Proportion of batch, l / kg : 5,0-6,0/25

Time of use, min, not less than: 20 min

Substrate temperature, ° С: +10 to +25

Compressive strength, MPa, not less than: 15.0

Ready for use: after 7-28 days

Consumption, kg / m2 / mm: around 1.6

LAYER THICKNESS 5 – 20 mm

CONVENIENT IN APPLICATION

PERSISTENT TO THE CONCENTRATED LOAD

HIGH STRENGTH

PERFECTLY SMOOTH SURFACE

DOES NOT BURN

ECOLOGICALLY CLEAN

Mixture “Artisan” Ц.2.ПР1

ДСТУ БВ.2.7-126:2011

Hygienic conclusion of the Ministry of Health of Ukraine.

APPLICATION

The solution is used for manufacturing self-leveling floors on almost any pre-prepared basis, in residential and public premises. The thickness of the layer is not more than 15 mm. Pour into 1 coat. The finished screed meets all the requirements of finishing floors, which can be applied to all types of coatings (parquet, linoleum, carpet, tile, paint, etc.).

PREPARATION OF THE SURFACE

The most important factor is the preparation of the base. The basic requirement – the basis should be strong and clean (aging of cement bases – 28 days). ). Before applying the floors from the base, it is necessary to remove not only coarse dirt, but even dust, preferably with a vacuum cleaner. To remove oils, fats, wax, paraffin, paints and other contaminants from the surface of the substrate, it is necessary to use alkaline solutions, and then rinse with water. Large damages, for example, broken pieces of screed, cracks or voids should be removed and plastered. All the grounds must be treated with Primer “Artisan No. 7”. Do not wet the surface of the base with water.

PERFORMANCE OF WORK

The mixture is mixed with water approximately on a bag of 25 kg – up to 6 liters of water and mixed using a stirrer with low speed, until a homogeneous mass without lumps. Wait 5 minutes and mix again. Then pour the solution onto the prepared substrate and distribute it with a roller, a hard broom, a rubber bar and similar tools. It is recommended to roll over the surface of the poured layer with a spiked roller to remove air plugs. You can use a piston or auger pump to feed the solution. In cause of a break in operation for more than 20 minutes, the machine should be cleaned with water. The hardened solution can only be removed mechanically. The diluted solution must be protected from drying.

NOTE!

Excess water reduces the mechanical strength of the solution, the solution can be delaminated. Keep away from high temperatures and drafts. After 8 hours, the floor is ready for use. The manufacturer is not responsible for improper use of the material, as well as its application in order and conditions not stipulated by the instruction.

SAFETY PRECAUTIONS

The mixture contains cement, which, when mixed with water, forms an alkali. Work should be in rubber gloves. If the solution gets into the skin or eyes, rinse them with plenty of water, if necessary, consult a doctor.

EXPIRATION DATE

In dry conditions and hermetic packaging the period of storage is at least 12 months from the date of manufacture.

PACKAGING

The dry mix is packaged in bags of 25 kg.

TECHNICAL CHARACTERISTICS

Composition: Mixture of cement with mineral fillers and special additives

Proportion of the mixture, l / kg: 0,22 – 0,24

Time of use, min:  to 20

Application temperature, ° С: from +5 to +30

Compressive strength, MPa, not less than: 15,0

Readiness for operation, hours, after: 36

Consumption, kg / m2 / mm, approx.: 1,5

LAYER THICKNESS 2-15 MM

SUSTAINABLE TO CONCENTRATED LOAD

HIGH-STRENGTH

PERFECT SMOOTH SURFACE

CONVENIENT IN APPLICATION

DOES NOT BURN

ENVIRONMENTALLY PURE

Mixture “Artisan” Ц.2.ПР2

ДСТУ БВ.2.7-126:2011

Hygienic conclusion of the Ministry of Health of Ukraine.

APPLICATION

The solution is used for manufacturing self-leveling floors on almost any pre-prepared basis, in residential and public premises. The thickness of the layer is not more than 10 mm. Pour into 1 coat. The finished screed meets all the requirements of finishing floors, which can be applied to all types of coatings (parquet, linoleum, carpet, tile, paint, etc.).

PREPARATION OF THE SURFACE

The most important factor is the preparation of the base. The basic requirement – the basis should be strong and clean (aging of cement bases – 28 days). Before applying the floors from the base, it is necessary to remove not only coarse dirt, but even dust, preferably with a vacuum cleaner. Large damages, for example, broken pieces of screed, cracks or voids should be removed and plastered. All the grounds must be treated with Primer “Artisan No. 7”. Do not wet the surface of the base with water.

PERFORMANCE OF WORK

The mixture is mixed with water approximately on a bag of 25 kg – up to 6 liters of water and mixed using a stirrer with low speed, until a homogeneous mass without lumps. Wait 5 minutes and mix again. Then pour the solution onto the prepared substrate and distribute it with a roller, a hard broom, a rubber bar and similar tools. It is recommended to roll over the surface of the poured layer with a spiked roller to remove air plugs. You can use a piston or auger pump to feed the solution. In cause of a break in operation for more than 20 minutes, the machine should be cleaned with water. The hardened solution can only be removed mechanically. The diluted solution must be protected from drying.

NOTE!

Excess water reduces the mechanical strength of the solution, the solution can be delaminated. Keep away from high temperatures and drafts. After 8 hours, the floor is ready for use. It is possible to apply various coatings to the floor surface after 7-28 days, taking into account the requirements ДБН В.2.6-22-2001.

The manufacturer is not responsible for improper use of the material, as well as its application in order and conditions not stipulated by the instruction.

SAFETY PRECAUTIONS

The mixture contains cement, which, when mixed with water, forms an alkali. Work should be in rubber gloves. If the solution gets into the skin or eyes, rinse them with plenty of water, if necessary, consult a doctor.

EXPIRATION DATE

In dry conditions and hermetic packaging the period of storage is at least 12 months from the date of manufacture.

PACKAGING

The dry mix is packaged in bags of 25 kg.

TECHNICAL CHARACTERISTICS

Composition: Mixture of cement with mineral fillers and special additives

Proportion of the mixture, l / kg: 5,5-6/25

Time of use, min, not less than: 20

Application temperature, ° С: from +5 to +30

Compressive strength, MPa, not less than: 15

Readiness for operation, hours, after: 8

Consumption, kg / m2 / mm, approx.: 1.6

LAYER THICKNESS 2-10 MM

CONVENIENT IN APPLICATION

FAST CURING

HIGH-STRENGTH

PERFECT SMOOTH SURFACE

DOES NOT BURN

ENVIRONMENTALLY PURE

Mixture “Artisan” Ц.2.ПР1

ДСТУ БВ.2.7-126:2011

Hygienic conclusion of the Ministry of Health of Ukraine.