Adhesive mixture for mineral cotton plates C-14

Adhesive mixture for mineral cotton plates C-14 – for gluing mineral wool slabs and performing reinforcing layer


The mixture is used in the facade warming system with an “easy wet” method for gluing mineral wool plates and performing the reinforcement layer. The mixture is elastic, has good adhesion to the base and mineral wool plates.


The substrate should be smooth, dry, durable, free from grease, old paints and other materials that reduce adhesion. Loose, weak layer must be removed. Base before applying the mortar mixture to treat with primer No. 7 or, if necessary, with primer No. 8 of the trade mark “Artisan”.

! It is recommended to check the adhesion of the samples of the mineral wool plate (15 x 15 cm) to the base. After 3 days, check the reliability of the adhesion to peel.


The dry mixture is mixed manually or mechanically with clean water until a uniform consistency is obtained. Leave the mixture for 3-5 minutes, then mix again. The solution can then be used for about 2 hours. For gluing the plates, the prepared mortar mixture is applied along the perimeter of the plates by a strip (width 4-5 cm). In the center of the plate, 6-8 spots are formed, not less than 1 cm high and about 10 cm in diameter. This allows further alignment of the plates relative to each other. Covered with mortar, the area should be at least 40% of the area of the slab.

It is allowed to glue the glazing plates with Artisan C-13 glue. Apply glue to the entire surface with a notched trowel 8 x 8 or 10 x 10 mm can only be, having a flat base.

! The solution should not fall on the end plates, the excess solution must be removed.

! Helpful advice: first we recommend making a thin contact layer on the perimeter of the mineral wool board and in places where the spots of the solution will form. This will greatly facilitate further work on the installation of slabs.

To make a reinforcing layer of plaster it is necessary to proceed 72 hours after gluing the plates. A mortar mixture with a thin layer is applied with an even side of the spatula. The grooved side forms furrows. The fiberglass mesh is pressed into the adhesive solution.

The applied solution is leveled with a flat spatula. In this case, the lathing should be located inside the layer of the adhesive solution. After drying, apply a thin layer of C-14 to remove the waffle pattern.

Careful implementation of the reinforcing layer is very important from both a constructive point of view and an aesthetic one. Popouts must be carefully sanded so that they are not visible through a thin layer of decorative plaster. All recommendations are valid at a temperature of 20 ° C and a relative humidity of 60%. In the production of works should be guided by the current building codes and regulations.

The manufacturer is not responsible for the misuse of the material, nor for its use for purposes and conditions not provided for by the instruction.


The mixture contains cement, which when combined with water forms alkali. Avoid contact with the skin and mucous membranes. Be sure to work in rubber gloves. In case of contact with the skin and eyes, rinse thoroughly with water.


In dry conditions and hermetic packaging the period of storage is at least 12 months from the date of manufacture.


The dry mix is packaged in bags of 25 kg.


Composition: a mixture of white cement with mineral fillers and special additives

Quantity of water for solution preparation, l / kg :  0,22 – 0,24

Time of use, min, not less than: 120

Open time, min, not less than20

Correction time, min, not less than: 10

Strength of adhesion to the base, MPa, not less than: 0,5

Temperature of use, ° С: from +10 to +30

Consumption, kg / m2 :

As an adhesive for slabs: around 6

        As a reinforcing layer: around 5












Mixture “Artisan” C.1.ЗК5-ГІ3

DSTU BV.2.7-126: 2011

Hygienic conclusion of the Ministry of Health of Ukraine


There are no reviews yet.

Be the first to review “Adhesive mixture for mineral cotton plates C-14”

Your email address will not be published. Required fields are marked *